Garage Door Torsion Spring Repair

    Is your garage door not opening or stuck wide open? Looking for a professional repair technician?

    call our garage door repair team now.

    CALL ☎️ (410) 469-1032

    Or, fill out this form and we will contact you shortly

    How Long Does a Garage Door Last

    When it comes to the garage door torsion spring repair, it is essential that you understand the risks.

    It is extremely dangerous.

    Hence, only the skilled technicians in the area of garage door repair in Baltimore should do it.

    However, to give you a glimpse of how to do the garage door torsion spring repair, here are some of the steps:

    Prepare for the job.

    Before attempting to do the garage door torsion spring repair, you should first disconnect the garage door opener while the door is closed.

    Just unplug the opener from the door by means of pulling the release cord.

    Clamp one of the vice-grip pliers into the vertical track that is located above the rollers.

    This is to prevent the garage door from opening when the torsion springs have been installed.

    Start the removal and replacement of the springs.

    From the old springs that still hold tension, just insert a winding bar to the winding cone.

    Then, utilize a socket wrench to remove the setting or the holding screws slowly.

    This will then have the tension released on the winding bar.

    Then, simply remove the tension and stop when the winding bar is now facing the floor and is pressed on the door.

    Afterward, place the second winding bar to the winding cone, then lift it up to detach the first winding bar.

    After that, simply detach the second winding bar until it has been pointed to the floor.

    Utilize the two winding bars in order to remove the tension, by turning it one-quarter at a time.

    Just remember to be patient and never to place your hand on the springs just to attain stability.

    When you use the winding bars, keep in mind to place them away from the face and the clothes.

    After you have completely unwound the two springs and they now have zero tension, proceed to the removal of the center bolts, which connect the two springs together.

    Then, loosen the cable drums and have the cable released.

    Pull each drum to the middle of the torsion shaft afterward.

    After that has been down, simply file down some screw marks on the shaft.

    Then, pull the shaft out of the rear bracket, then have the cable drum removed, as well as the spring.

    Place the new spring on the torsion shaft and ensure that the red winding cone is placed on the garage’s left side.

    The opposite spring should have a winding cone that is black.

    Simply have these steps repeated about seven and eight on the other side.

    Fasten it.

    As you place the torsion shaft into place, simply place the springs back at the center.

    Then, reattach the cable to the cable drum at the left, and then run it.

    Fasten the drum onto the shaft afterward.

    Using the cable taut, place a vice-grip to the torsion shaft and have it secured against the header.

    Place the cable to the cable drum at the right, then run it again, and have it fastened onto the shaft.

    As for the springs, insert the winding bar for the left spring into the cone and have it rotate towards the header.

    Place a second winding bar into the cone and then place it against the door.

    Simply remove the other winding bar, and then lift it upward for a turn, about a quarter.

    You should look into the instruction manual for the specific quarter turns that are required.

    The seven-foot doors typically need about 31 quarter turns, while the eight-foot ones need about 34 turns.

    Once you have finished the turns, just leave one winding bar into the cone and permit it to press against the door securely.

    Then, fasten the set screws that are found on the left side of the torsion spring.

    Remember that if you cannot do any of these, reach out to a garage door repair in Baltimore.

    Call Smooth Openers

    A garage door spring repair is a huge undertaking.

    However, Smooth Openers can easily do it.

    We are a team of professionals and experts who operate for the needs and satisfaction of our clients.

    We offer a wide range of services, ranging from garage door installation in Baltimore to garage door repair.

    Do not hesitate to contact us should you need any help!

    Call Smooth Openers for the health of your garage door!

    Rate this post
    Contact Us
    Our technicians are equipped with masks and gloves complying with health and safety regulations.
    This is default text for notification bar